The short version
- A conventional loan is any mortgage not insured or guaranteed by the government (not FHA, VA, or USDA).
- A conforming loan is a conventional loan that meets Fannie Mae and Freddie Mac rules, including the loan-size limit.
- For 2026, the baseline conforming limit for a one-unit home is $832,750. In high-cost areas the ceiling is $1,249,125. These limits change every year.
- A loan above the limit is a jumbo (non-conforming) loan. Alt-A and subprime loans are also non-conforming.
Conventional vs. government
Think of it as two big buckets:
| Conventional | Government |
|---|---|
| No government insurance or guarantee | Insured or guaranteed by a federal agency |
| Private mortgage insurance (PMI) if the down payment is under 20% | FHA uses MIP; VA uses a funding fee; USDA uses a guarantee fee |
| Includes conforming and non-conforming loans | FHA, VA, USDA |
Fannie Mae and Freddie Mac (the GSEs)
- Fannie Mae is the Federal National Mortgage Association (FNMA).
- Freddie Mac is the Federal Home Loan Mortgage Corporation (FHLMC).
Both are government-sponsored enterprises (GSEs). They don’t lend money to borrowers. Instead they buy loans from lenders on the secondary market, bundle them into mortgage-backed securities (MBS), and sell those to investors. That gives lenders fresh cash to make more loans.
Since September 2008, both have been in conservatorship under the Federal Housing Finance Agency (FHFA), which regulates them and sets the conforming loan limits each year.
(Don’t confuse them with Ginnie Mae, the Government National Mortgage Association, a government agency inside HUD that guarantees MBS made of FHA, VA, and USDA loans. More in the secondary market chapter.)
Conforming loans
A loan is conforming when it meets the GSEs’ standards: loan size, credit, debt-to-income, documentation, and property rules. The size limit is the one tested most.
2026 conforming loan limits (one-unit property)
Set by FHFA and announced in November 2025:
| Area | 2026 limit |
|---|---|
| Baseline (most of the U.S.) | $832,750 |
| High-cost area ceiling | $1,249,125 (150% of the baseline) |
| Alaska, Hawaii, Guam, U.S. Virgin Islands: baseline | $1,249,125 |
| Alaska, Hawaii, Guam, U.S. Virgin Islands: ceiling | $1,873,675 |
The baseline rose 3.26% from 2025’s $806,500, matching FHFA’s measure of home price growth. FHFA resets these every year, so always check the current year. Two- to four-unit properties have higher limits.
“High-balance” conforming
A loan above the baseline but at or under the local high-cost limit is still conforming. Lenders often call it “high-balance” or “super-conforming.”
Non-conforming loans
Any conventional loan that doesn’t meet GSE rules:
- Jumbo: bigger than the conforming limit for the area. Usually needs stronger credit, larger reserves, and a bigger down payment because the lender (or a private investor) keeps all the risk.
- Alt-A: borrowers with decent credit but non-standard documentation (for example, limited income verification). Riskier than prime, less risky than subprime.
- Subprime: loans to borrowers with weaker credit, at higher rates to offset the risk.
Private mortgage insurance (PMI)
On a conventional loan with less than 20% down (loan-to-value, or LTV, over 80%), the lender usually requires PMI. It protects the lender, not the borrower, if the borrower defaults.
Under the Homeowners Protection Act (HPA), for most loans on a primary residence:
- The borrower can ask to cancel PMI when the balance reaches 80% of the home’s original value (with a good payment history).
- PMI automatically ends when the balance is scheduled to hit 78% of the original value, if the borrower is current.
- PMI must end no later than the midpoint of the loan’s amortization schedule (for example, year 15 on a 30-year loan), if the borrower is current.
Numbers to memorize
| Item | Number |
|---|---|
| 2026 baseline conforming limit (1 unit) | $832,750 (changes yearly) |
| 2026 high-cost ceiling (1 unit) | $1,249,125 (changes yearly) |
| 2025 baseline (for comparison) | $806,500 |
| High-cost ceiling as % of baseline | 150% |
| PMI usually required when down payment is under | 20% (LTV over 80%) |
| Borrower may request PMI cancellation | 80% of original value |
| PMI automatic termination | 78% of original value |
| PMI final termination | Midpoint of amortization |
| GSE conservatorship began | September 2008 |
Memory tricks
- Conventional = “Not the government.” Conforming = “Conforms to Fannie/Freddie.”
- All conforming loans are conventional, but not all conventional loans are conforming. (Like: all squares are rectangles.)
- Fannie and Freddie are shoppers, not lenders. They buy loans; they don’t make them.
- PMI: “Ask at 80, auto at 78.”
Watch out on the exam
- “An FHA loan is a conforming loan.” No. FHA is government, not conventional. “Conforming” only describes conventional loans.
- “Jumbo” means non-conforming because of size, not because of the borrower’s credit.
- Who sets the conforming loan limit? FHFA, not Fannie Mae, not HUD, not the CFPB.
- PMI protects the lender. A choice saying it protects the borrower is the trap.
- Watch for old limits in a question. The exam may ask the concept (baseline vs. high-cost) more than the dollar figure, which changes yearly.